Updated bluepill for new tmpl update

LICENSE

@@ -1,3 +1,6 @@
+MIT License
+
+Copyright (c) 2018 Guillaume P.
 Copyright (c) 2020 Joey Hines
 
 Permission is hereby granted, free of charge, to any person obtaining a copy

README.md

@@ -1,7 +1,9 @@
-# Rust Template
+# Rust Bluepill Template
 
 A template for my Rust projects. Uses [tmpl](https://git.jojodev.com/jolheiser/tmpl).
 
+Inspiration: [blue-pill-quickstart](https://github.com/TeXitoi/blue-pill-quickstart)
+
 ## License
 
 [MIT](LICENSE)

template/.cargo/config

@@ -0,0 +1,7 @@
+[target.thumbv7m-none-eabi]
+runner = "{{runner}}"
+
+rustflags = ["-C", "link-arg=-Tlink.x"]
+
+[build]
+target = "thumbv7m-none-eabi"

template/Cargo.toml

@@ -7,3 +7,7 @@ edition = "{{rust_edition}}"
 # See more keys and their definitions at https://doc.rust-lang.org/cargo/reference/manifest.html
 
 [dependencies]
+stm32f1xx-hal = { version = "0.7", features = ["rt", "stm32f103" ] }
+cortex-m = "0.7"
+cortex-m-rt = { version = "0.6", features = ["device"] }
+panic-semihosting = "0.5"

template/memory.x

@@ -0,0 +1,6 @@
+/* Linker script for the STM32F103C8T6 */
+MEMORY
+{
+  FLASH : ORIGIN = 0x08000000, LENGTH = 64K
+  RAM : ORIGIN = 0x20000000, LENGTH = 20K
+}

template/openocd.cfg

@@ -0,0 +1,2 @@
+source [find interface/stlink-v2.cfg]
+source [find target/stm32f1x.cfg]

template/openocd.gdb

@@ -0,0 +1,10 @@
+target remote :3333
+set print asm-demangle on
+monitor arm semihosting enable
+
+# detect unhandled exceptions, hard faults and panics
+break DefaultHandler
+break HardFault
+break rust_begin_unwind
+
+load

template/src/main.rs

@@ -1,3 +1,53 @@
-fn main() {
-    println!("Hello, world!");
+//! Blinks an LED
+//!
+//! This assumes that a LED is connected to pc13 as is the case on the blue pill board.
+//!
+//! Note: Without additional hardware, PC13 should not be used to drive an LED, see page 5.1.2 of
+//! the reference manual for an explanation. This is not an issue on the blue pill.
+//! Taken from https://github.com/stm32-rs/stm32f1xx-hal/blob/master/examples/blinky.rs
+
+#![deny(unsafe_code)]
+#![no_std]
+#![no_main]
+
+use panic_halt as _;
+
+use nb::block;
+
+use cortex_m_rt::entry;
+use embedded_hal::digital::v2::OutputPin;
+use stm32f1xx_hal::{pac, prelude::*, timer::Timer};
+
+#[entry]
+fn main() -> ! {
+    // Get access to the core peripherals from the cortex-m crate
+    let cp = cortex_m::Peripherals::take().unwrap();
+    // Get access to the device specific peripherals from the peripheral access crate
+    let dp = pac::Peripherals::take().unwrap();
+
+    // Take ownership over the raw flash and rcc devices and convert them into the corresponding
+    // HAL structs
+    let mut flash = dp.FLASH.constrain();
+    let mut rcc = dp.RCC.constrain();
+
+    // Freeze the configuration of all the clocks in the system and store the frozen frequencies in
+    // `clocks`
+    let clocks = rcc.cfgr.freeze(&mut flash.acr);
+
+    // Acquire the GPIOC peripheral
+    let mut gpioc = dp.GPIOC.split(&mut rcc.apb2);
+
+    // Configure gpio C pin 13 as a push-pull output. The `crh` register is passed to the function
+    // in order to configure the port. For pins 0-7, crl should be passed instead.
+    let mut led = gpioc.pc13.into_push_pull_output(&mut gpioc.crh);
+    // Configure the syst timer to trigger an update every second
+    let mut timer = Timer::syst(cp.SYST, &clocks).start_count_down(1.hz());
+
+    // Wait for the timer to trigger an update and change the state of the LED
+    loop {
+        block!(timer.wait()).unwrap();
+        led.set_high().unwrap();
+        block!(timer.wait()).unwrap();
+        led.set_low().unwrap();
+    }
 }

tmpl.yaml

@@ -13,4 +13,8 @@ prompts:
     default: joey@ahines.net
   - id: rust_edition
     label: Rust Edition
-    default: 2021
+    default: "2021"
+  - id: runner
+    label: Run Command
+    default: "gdb-multiarch -q -x openocd.gdb"                    
+    help: "Command used by cargo run to start code on the target hw"